• Image 1
  • Image 2

Zebralight H52 AA Headlamp Cool White

Out of Stock


Product Description

Zebralight H52 Headlamp Cool White

House of Lumens is proud to offer the H52 from Zebralight. Powered by 1 AA Battery this LED headlamp can put out as much as 300 Lumens and as little as 0.01 Lumens. Easy operation and durable unibody aluminum construction make the Zebralight H52 your only choice for work or pleasure. From getting an early start at a job site to Hiking, Biking and boating and dont forget when your under the kitchen sink to fix that plumbing leak. the freedom of hands free lighting makes all of your adventures a lot easier.

Basic Operation

One quick-click turns on the light to High or turns off the light.
Two quick-clicks turns on the light to Medium.
Three quick-clicks turns on the light to the beacon-strobe mode.
Press and hold (for over 0.6 seconds) turns on the light to Low and then Medium and High. Release at the desired level.

Advanced Operation and Configuration

Press and hold to cycle from Low, Medium and High, release at the desired level to set. When you press and hold, the light will always cycle from Low to High, regardless which level you are currently in.

Double click to toggle and select between the two sub-levels for that main level. Sub-level selections for the 3 main levels are memorized after the light is turned off and through battery changes.

The second sub-level (H2, M2 and L2) of each main levels can be further programmed to different brightness levels. At a main level, double-click 6 times to start configuration. On subsequent double-clicks the light will cycle through different brightness levels. Short click to turn off the light when finishing configurations. The selections for the second sub-levels are memorized after the light is turned off and through battery changes.

This light uses the main LED (flashing 1 to 4 times) to indicate the estimated remaining capacity of the battery. To start the battery indicator, (from Off) short-click 4 times without pause.

Beacon-strobe mode can be accessed from 3 short-clicks when the light is Off. Once in the beacon-strobe mode, you can double-click to cycle from the beacon to strobe and back. Beacon-strobe settings are memorized when the light is turned off and through battery changes.

Technical Specs

  • Battery capacity indicator. Activated by 4 short clicks and LED flashes 1-4 times
  • All light levels are current regulated
  • Low battery alert. LED will flash (when light is turned off) when battery voltage drops below 1.06 volts
  • Light level will automatically step down to lower levels when battery capacity is getting low, to extend run time
  • Built in over discharge protection for 14500 Lithium Ion battery. cut off at 2.8 volts
  • Durable quiet electronic soft touch switch
  • Smart user interface (UI) for fast easy access to all brightness levels, beacons and strobes
  • Precision machined uni body casing made from premium grade aluminum bar stock
  • Proprietary heat sink, bonds LED board directly to unibody casing for excellent heat dispersion
  • Type III Class I hard anodized natural finish
  • Sealed and potted LED driver circuit
  • Battery power can be disconnected by slightly unscrewing tailcap, prevents accidental light activations or battery drain
  • Waterproof tested to ANSI standard IPX7 ( 2 meters for 30 Min.)

Extended Information

  • LED: Cree XM-L2 Cool White
  • User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.
  • Light Output and run-times
    • High: H1 300 Lumens (0.9 hrs) or H2 184 Lumens (1.7 hrs) / 116 Lumens (3 hrs)
    • Medium: M1 54 Lumens (7.5 hrs) or M2 27Lumens (12 hrs) / 13 Lumens (27 hrs)
    • Low: L1 2.9 Lumens (4 days) or L2 0.36 Lumens (3 weeks) / 0.06 Lumens (2 months) / 0.01 Lumens (3 months)
    • Beacon Strobe Mode: 4Hz Strobe at H1 / 19Hz Strobe at H1
    • Light output are ANSI out the front (OTF) values. Run-times tested (and parasitic drain estimated) using Sanyo 2000mAh Eneloop AA battery. Light output with 14500 Lithium Ion battery is the same except that the H1 is 535 Lumens for the first minute and then step down to 300 Lumens.
  • Operating Voltage Range: 0.7V - 4.2V
  • Battery: One 1.5V AA (NiMH, lithium or alkaline) or 3.7V 14500 lithium ion rechargeable. Batteries are not included in the package.
  • Parasitic Drain: Negligible (much less than the self discharging of a battery)
  • Beam Type
    • 80 degree spill
    • 12 degree hot spot
  • Dimensions
    • Head Diameter: 0.86 inch (21.8 mm)
    • Length: 3 inch (76.5 mm)
  • Weight
    • 1.1 oz (32 gram)
    • 2.9 oz (80 gram) with an Eneloop AA and headband

Product Reviews

Write Review

This product hasn't received any reviews yet. Be the first to review this product!

0.50 LBS
Calculated at checkout